Smeg P23LINP Guia de Resolução de Problemas Página 14
- Página / 15
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Classic models : The control knob is located on the
lower right hand side of the outer case. It is marked as
shown in figure 2;
Linear models : The control knob is located on the
l
ower right hand side of the outer case. It is marked as
shown in figure 3;
Fab models : The control knob is located on the
lower right hand side of the outer case. It is of a spher-
ical design and is marked as shown in figure 4;
The pilot is visible behind the left hand side of the burner. Push in and turn the control knob
to the SPARK position, and hold there for a few seconds. Continue turning anti-clockwise
through the spark click to the PILOT light position, ensuring the pilot has lit. If not, return
the knob clockwise, and repeat.
When the pilot lights after the spark, keep the knob pressed for approximately ten seconds.
Now release the knob and the pilot should stay alight. If the pilot is extinguished during use,
wait three minutes before repeating the ignition procedure.
To achieve the HIGH setting, push the control knob in slightly and continue turning anti-
clockwise to the high position. The main burner should light after a few seconds. To
decrease the setting to low, turn the control knob clockwise to the LOW setting.
To turn to the PILOT position from the HIGH or LOW positions, press the control knob
in, and return to the pilot position and release. To turn the fire off, keep the knob pressed
in, return to the OFF position and release.
This fire is fitted with a combustion monitoring safety device (ODS). If the appliance shuts down during use for no apparent rea-
son then several reasons may be suspected.
If a door or window has been opened creating a draught, then pilot disturbance could be the problem and removal of the draught
should resolve this. The appliance can then be re-lit in accordance with the previous section. If pilot disturbance is not the cause,
then the ODS safety system may be in operation. Switch the appliance OFF, call in your installer to check the appliance and ven-
tilation. Remedial work must be carried out as required. DO NOT allow the appliance to be used until the appliance and instal-
lation is passed as safe.
If the pilot continues to be extinguished, you must call your installer to check the operation of the complete appliance.
Before carrying out any of the following operations, ensure that the appliance is OFF and completely cold.
Regularly clean around the appliance to ensure that dust, fluff, pet hair etc, are kept to a minimum. There are no other specific
requirements for care, other than regular cleaning of the general appliance. A wipe with a dry cloth is normally sufficient. DO
NOT use abrasive cleaners as they can damage the finish. Metal parts may be cleaned using an appropriate metal cleaner. Test
on a hidden part before cleaning. Clean only in the direction of the grain.
GLASS PANEL - This can be cleaned with a suitable glass cleaner. Test on a small area first.
PAINTED AREAS - These can be cleaned using a dry cloth.
FINISHED METAL AREAS - These can either be cleaned using a proprietory metal cleaner. Test on a small hidden part before
cleaning. Always clean in the direction of the grain.
4.0 OPERATING THE APPLIANCE
‘OFF’ position
‘SPARK’ position
‘LOW’ position
‘HIGH’ position
Figure 2
Figure 3
Figure 4
5.0 COMBUSTION MONITORING SYSTEM
6.0 CLEANING
© 2008 Smeg S.p.A.
GB IE
GB-IE-3
Smeg EU-wide instal instruc-v7-English.qxp:Smeg EU-wide installation instructions DRAFT A-12-12-07.qxd 17/7/08 12:07 Page 14
- 2008 Smeg S.p.A 1
- 2.0 APPLIANCE DATA 3
- 3.0 INSTALLATION REQUIREMENTS 3
- 3.1 ROOM SIZING 3
- 4.0 SITE REQUIREMENTS 4
- 4.1 VENTILATION 4
- 5.0 UNPACKING THE APPLIANCE 5
- 5.1 COMPONENT CHECKLIST 5
- 6.0 GAS SUPPLY ROUTES 5
- 7.0 FIXING THE APPLIANCE 5
- 7.0 FIXING THE APPLIANCE ( 6
- 8.0 TESTING AND COMMISSIONING 6
- 8.1 OPERATING THE APPLIANCE 7
- 8.2 SETTING PRESSURE 7
- 9.0 BRIEFING THE CUSTOMER 8
- 10.0 SERVICING 8
- 10.2 PILOT ASSEMBLY 9
- 10.3 CATALYSTS 10
- 11.0 TROUBLESHOOTING GUIDE 11
- 1.0 IMPORTANT NOTES 12
- CONTINUED) 13
- 4.0 OPERATING THE APPLIANCE 14
- 6.0 CLEANING 14
- 9.0 INSTALLATION DETAILS 15
- 10.0 SERVICE HISTORY 15
- 7.0 SERVICING 15
- 8.0 LIST OF REPLACEMENT PARTS 15
Manuais e produtos relacionados com Lareiras Smeg P23LINP
(7 páginas)Whirlpool AKP 292/IX manuales
Manuales del propietario y guías del usuario para Hornos Whirlpool AKP 292/IX.
Ofrecemos 1 manuales en pdf Whirlpool AKP 292/IX para descargar gratis por tipos de documentos: Instrucciones de uso
Comentários a estes Manuais